ACT series 

The double regulation system allows you to cover a whole variety of combinations between air and product flows which are not normally obtainable with our conventional spray guns.

The true HVLP. The special ACT-S and ACT-AS spray guns allow the spray application with the HVLP system of various coatings and solvent or water based paints on different surfaces (metal, wood, laminates, rocks, walls…) in several industrial and decorative sectors like joinery, carpentry, car body and garage works, boat maintenance etc. The ACT-S model, due to its gravity fed upper tank with air regulator is suitable also for applying specially heavy, thick or sticky varnishes, wall paints and coatings while the ACT-AS model, with its bottom tank equipped with safety closure, is mostly suitable for light or low viscosity products. The peculiarity of these new models consists in the possibility to independently set both the amount of product sprayed and the air flow that produces its vaporization with the added possibility to modify at will the width of the sprayed pattern.

ACT-AS

The spray gun with a bottom metal tank combined with TMR Turbines enables spraying of different covering materials, water or solvent-based paints on different media

TECHNICAL DATA SHEET

TankLower cup  1lt
BodyAluminium silver teflon coated
Air cupRed & Blue
Product quantity regulationSpecific rear screw
Air flow regulationSpecific rear screw
Quantity of delivered air 1100/2500 l/min
Turbines compatibilityRecomended use with E series TMR turbines. Also usable with TMR 80 and 140
Spraying materialsWater and solvents* based varnishes water paints (see chart uses)
Nozzles available 0.7 / 1.0 / 1.3 / 1.7 / 2.1 / 2.5 / 3.0 / 3.5 mm 
Weight1 kg 
Gun materialPTFE coated metal body
Tank materialAluminium tank with safety closure

- 100% Rigo, original and registered design

- All metal body, Teflon finished

- High quality metal components

- Air discharge blocking system when gun lever is not pulled.

- Independent air flow and product amount regulations

- Possibility to modify at will the width of the sprayed pattern

- Equipped with several accessories

- Tested over 500.000 cycles.

- Product Transfer efficiency up to 85%,

- Limited overspray, product waste reduction

- Time saving up to 60% in respect to roller and brush

- Complies to VOC regulations

- Air volume and pressure always in optimal ratio

- High quality application finish, with clean and narrow (2 – 3 cm wide)

  mark, suitable for writing, decorating or

  for finishing touches to already done jobs

- Suitable for spraying most of the modern coatings

- Efficient of industrial and handcraft professional jobs

- It allows accurate and safe works

- Reduced maintenance and easy cleaning.

It comes with 2 air cups (blue & red) , all the noozles and a heat resistant handgrip. 

ACT-S

The ACT-S spray gun with a gravity 750ml tank with regulator air amount at the top of the container may be combined with all turbines RIGO and to spray water or solvent based paints to metal, wood, masonry etc. through HVLP system

TECHNICAL DATA SHEET

TankUpper gravity with screw closure 0,6 lt
BodyAluminium silver teflon coated
Air cupRed & Blue
Product quantity regulationSpecific rear screw
Air flow regulationSpecific rear screw
Quantity of delivered air 1100/2500 l/min
Turbines compatibilityRecomended use with E series TMR turbines. Also usable with TMR 80 and 140
Spraying materialsWater and solvents* based varnishes water paints (see chart uses)
Nozzles available 0.7 / 1.0 / 1.3 / 1.7 / 2.1 / 2.5 / 3.0 / 3.5 mm 
Weight700 gr 
Gun materialPTFE coated metal body
Tank materialSolvent proof tank 600gr with air regulator

- 100% Rigo, original and registered design

- All metal body, Teflon finished

- High quality metal components

- Air discharge blocking system when gun lever is not pulled.

- Independent air flow and product amount regulations

- Possibility to modify at will the width of the sprayed pattern

- Equipped with several accessories

- Tested over 500.000 cycles.

- Product Transfer efficiency up to 85%,

- Limited overspray, product waste reduction

- Time saving up to 60% in respect to roller and brush

- Complies to VOC regulations

- Air volume and pressure always in optimal ratio

- High quality application finish, with clean and narrow (2 – 3 cm wide)

  mark, suitable for writing, decorating or

  for finishing touches to already done jobs

- Suitable for spraying most of the modern coatings

- Efficient of industrial and handcraft professional jobs

- It allows accurate and safe works

- Reduced maintenance and easy cleaning.

It comes with 2 air cups (blue & red) , all the noozles and a heat resistant handgrip.

ACT

The ACT spray gun may be combined with all turbines RIGO and to spray water or solvent based paints to metal, wood, masonry etc. through HVLP system with pressure tank 2/9/18 lt

TECHNICAL DATA SHEET

Tankconnect with any type of pressure tank together with TMR turmines
BodyAluminium silver teflon coated
Air cupRed & Blue
Product quantity regulationSpecific rear screw
Air flow regulationSpecific rear screw
Quantity of delivered air 1100/2500 l/min
Turbines compatibilityRecomended use with E series TMR turbines. Also usable with TMR 80 and 140 Not recomended with TMR55
Spraying materialsWater and solvents* based varnishes water paints (see chart uses)
Nozzles available 0.7 / 1.0 / 1.3 / 1.7 / 2.1 / 2.5 / 3.0 / 3.5 mm 
Weight500 gr 
Air supplyFrom TMR
 Product supplyFrom 9 and 18 lt tank

- 100% Rigo, original and registered design

- All metal body, Teflon finished

- High quality metal components

- Air discharge blocking system when gun lever is not pulled.

- Independent air flow and product amount regulations

- Possibility to modify at will the width of the sprayed pattern

- Equipped with several accessories

- Tested over 500.000 cycles.

- Product Transfer efficiency up to 85%,

- Limited overspray, product waste reduction

- Time saving up to 60% in respect to roller and brush

- Complies to VOC regulations

- Air volume and pressure always in optimal ratio

- High quality application finish, with clean and narrow (2 – 3 cm wide) mark, suitable for writing, decorating or for finishing touches to already done jobs - Suitable for spraying most of the modern coatings - Efficient of industrial and handcraft professional jobs - It allows accurate and safe works - Reduced maintenance and easy cleaning

It comes with 2 air cups (blue & red) , all the noozles and a heat resistant handgrip.

ACT- XXL the professional

The spray gun XXL with the lance 80cm long is suitable for painting on “impossible” surfaces

With double regulation of air/product you can set working conditions that could not be achieved so far and perfectly suitable for your specific painting products

TECHNICAL DATA SHEET

Tankconnect with any type of pressure tank together with TMR turmines
BodyAluminium silver teflon coated
Air cupRed & Blue
Product quantity regulationSpecific rear screw
Air flow regulationSpecific rear screw
Quantity of delivered air 1100/2500 l/min
Turbines compatibilityRecomended use with E series TMR turbines. Also usable with TMR 80 and 140 Not recomended with TMR55
Spraying materialsWater and solvents* based varnishes water paints (see chart uses)
Nozzles available 0.7 / 1.0 / 1.3 / 1.7 / 2.1 / 2.5 / 3.0 / 3.5 mm 
Weight500 gr 
Air supplyFrom TMR
 Product supplyFrom 9 and 18 lt tank

- 100% Rigo, original and registered design

- All metal body, Teflon finished

- High quality metal components

- Air discharge blocking system when gun lever is not pulled.

- Independent air flow and product amount regulations

- Possibility to modify at will the width of the sprayed pattern

- Equipped with several accessories

- Tested over 500.000 cycles.

- Product Transfer efficiency up to 85%,

- Limited overspray, product waste reduction

- Time saving up to 60% in respect to roller and brush

- Complies to VOC regulations

- Air volume and pressure always in optimal ratio

- High quality application finish, with clean and narrow (2 – 3 cm wide) mark, suitable for writing, decorating or for finishing touches to already done jobs - Suitable for spraying most of the modern coatings - Efficient of industrial and handcraft professional jobs - It allows accurate and safe works - Reduced maintenance and easy cleaning

It comes with 2 air cups (blue & red) , all the noozles and a heat resistant handgrip.

ACT- L the professional

NEW! The spray gun of intermediate dimensions between ACT and ACT-XXL with the extension of 25cm suitable for use with Kombi and Cart Turbine. Ideal for treating floors while standing, perfect for painting of under ceilings and attics

TECHNICAL DATA SHEET

Tankconnect with any type of pressure tank together with TMR turmines
BodyAluminium silver teflon coated
Air cupRed & Blue
Product quantity regulationSpecific rear screw
Air flow regulationSpecific rear screw
Quantity of delivered air 1100/2500 l/min
Turbines compatibilityRecomended use with E series TMR turbines. Also usable with TMR 80 and 140 Not recomended with TMR55
Spraying materialsWater and solvents* based varnishes water paints (see chart uses)
Nozzles available 0.7 / 1.0 / 1.3 / 1.7 / 2.1 / 2.5 / 3.0 / 3.5 mm 
Weight500 gr 
Air supplyFrom TMR
 Product supplyFrom 9 and 18 lt tank

- 100% Rigo, original and registered design

- All metal body, Teflon finished

- High quality metal components

- Air discharge blocking system when gun lever is not pulled.

- Independent air flow and product amount regulations

- Possibility to modify at will the width of the sprayed pattern

- Equipped with several accessories

- Tested over 500.000 cycles.

- Product Transfer efficiency up to 85%,

- Limited overspray, product waste reduction

- Time saving up to 60% in respect to roller and brush

- Complies to VOC regulations

- Air volume and pressure always in optimal ratio

- High quality application finish, with clean and narrow (2 – 3 cm wide) mark, suitable for writing, decorating or for finishing touches to already done jobs - Suitable for spraying most of the modern coatings - Efficient of industrial and handcraft professional jobs - It allows accurate and safe works - Reduced maintenance and easy cleaning

It comes with 2 air cups (blue & red) , all the noozles and a heat resistant handgrip.

What is HVLP turbine ?

  • It is an ecological paint system that provides a high volume of air at low pressure (High Volume Low Pressure) .
  • The pressure turbine according to the range of 0.1 to 0,5 bar. The air flow rate can be adjusted from very low to very high speed. paint easily, quickly and with great accuracy.
  • Consumption of your materials is reduced due to minimal overspray (frost) -80%.
  • The air generated by the turbine does not need water trap is always dry, warm and dry as opposed to the air that produces air compressor.
  • The color dry more quickly and evenly spread on the surface. Ideal for all kinds of water or solvent paints.
  • Save up more thna 60% of materials !
Product added to wishlist
Product added to compare.

By continuing to use the website, you agree to the use of cookies.